Fitting A Cat Flap

Fitting a cat flap can be a bit daunting however it's actually quite simple by following the correct instructions. Find out how high you'd like your cat flap to be (normally it's located at the belly height). Mark this point on the door, and use the template as a reference to drill.

If you have a kitten who is still a baby and you want to keep the door open, gently prop it slightly open and allow it to go through. Reward it as it passes through.

Measure the Door

A cat flap is a wonderful method to let your pet leave and come in and out of your home whenever it pleases. This will keep your cat healthy as it ensures that it is getting enough exercise and be able to go back inside if it gets trapped outside during bad weather. This will cut down on the time you allow your cat in or out and also make your home secure by letting you know when it's gone.

It is important to ensure that the cat flap is installed properly to stop your pet from being pushed through through it by other animals (e.g. dogs). You should determine the height of your pet's belly as well as the size of the doorway at your home to make sure the flap is at the correct height. You can alter the height of your flap when your cat is taller or less than average.

Then, use a spirit-level to mark the center of the door. This is where you will install the flap. Utilizing the marking as a guide, take a jigsaw and cut out the shape of the flap inside the door. Once you've cut the area, sand the edges of the door to create smooth surfaces and drill any fixing holes needed.

Installing a cat flap ought to not take longer than two hours. The process is a bit more difficult if you have to install it in the form of a uPVC door or a composite one. This is due to the fact that these doors come in different thicknesses, which could affect the way that holes are cut. This is why we always recommend calling an expert to do the work, particularly if you have never worked with glass before.

Measure Your Cat

A cat flap can spare you from hours of hearing your pet's cries to let it out or in. This is particularly helpful when you're at work most of the day and your cat is stuck inside waiting until you get home in all weathers.

It is essential to measure your cat's measurements first before you begin the installation. While it may seem to be a simple task, it is crucial to measure the right way or your cat will be unable to use.

First, make sure your cat is calm prior to taking measurements. You'll need to hold them in a manner that they cannot move and ensure that the ruler or measuring tape is flat against their body and not arching in any places. Holding the ruler or measuring tape against their body from their head to the bottom of their tail can allow you to get an accurate measurement.

Once you've got the measurement of your cat, it's time to take a look at the door and decide where you want to place the flap. The best option is to position the flap on the highest point of your cat's stomach as it will allow them to get through it with minimal effort. This will also avoid the flap making lots of noise when it swings open and shut.

It is also important to think about the thickness and the structure of the uPVC door or composite. While timber doors are all of a similar thickness, upvc door panel with cat flap fitted and composite door cat flap doors can be very different in their overall construction and can make fitting a cat flap - More Material - more difficult since you have to make sure that the hole you make is the proper size for your pet.

You can also use the template included in the instructions to mark the location of the hole in the door. This will enable you to determine where the hole should be located and ensure that the template is placed precisely on the door. Utilizing a spirit level to check that the template is sitting right against the door will also prove beneficial.

Cut the Flap

You'll need to make a hole in the door to accommodate your cat flap before you can put it in place. This is a difficult job and it is recommended that you seek the help of a professional cat flap fitting service for this job in case you don't have the expertise or knowledge to do it yourself. You can also refer to the instructions provided with the kit to discover how to do it right.

You can use the height of the cat's or kitten's stomach as a reference. In general you should place the flap about 10-15 centimeters above the ground. This is the standard height of the stomach for cats. This way your cat will be able to go through the flap comfortably and also give other cats or snooping neighbours difficult time trying to get in or out.

Once you've decided the best location for the cat flap to be positioned, mark this position on the door with a pencil. Next, if your kit comes with a paper template, lay it on top of the door and use the markings to drill holes in each corner of the template. Then, you should be able cut out the design of the template and replace it with your cat flap.

If you are installing your cat flap on the form of a door made of wood or uPVC, you are able to do it yourself if feel confident enough to handle a jigsaw. Be careful not to cut into the mullions or rails that run vertically of your door. You can use a jigsaw to cut your panel into a square or a circle depending on the way you want it. Be patient and don't try to make the jigsaw cut faster.

After the hole has been made, carefully place the cat flap install flap in its new home. Make sure it's firmly secured. If it features caps on the screws, then place these onto the screws that protrude. Once the screws are in place, sand any rough edges of the cut then apply sealant to any gaps to ensure that there are no draughts coming into your home.

Fit the Flap

If you have a standard cat flap, you can try to encourage your pet through it by placing a small amount cat food on the front of the door. Alternately, you can push the cat through using your hand or a stick. Once your cat has become used to moving through the flap, it will be in a position to move as it pleases. This lets you let it in and out as it's wanted.

It is possible to fit the flap inside the UPVC doors or glass door, however it's not as easy as installing one on a wooden external door. This is due to the fact that the upvc door panel with cat flap doors and certain types of glass doors do not have an even thickness. This could have an enormous impact on how you cut out the flap hole and also whether the flap will fit correctly after installation.

Based on the type of cat flap you select It may include a mounting kit and a template that will show exactly where to drill holes for it. If the kit doesn't come with a template you can use a photocopier to create your own. It is important not to push the jigsaw too hard when cutting, so that it doesn't leave a bigger than necessary hole in your door.

Most cat flaps are square or rectangular in shape, however there are some that are circular and these are typically more difficult to place. If you have a round flap, ensure that the hole is in the correct place on your door. If not, your cat might not be able to access it, and could be locked outside for the entire day (or at night).

Certain cat flaps come with locks that let you determine when your cat is allowed to enter and leave. These are useful for pets who are afraid of leaving in the dark or returning in the dark. They are also useful when you are working all day. The lock can be turned on for entry or exit and some are locked in both directions, allowing you to shut the door completely. This is especially helpful for sick or elderly cats who aren't keen on going out in bad weather.