Fitting A Cat Flap

Fitting a cat flap can seem intimidating however it's actually quite simple with the proper instructions. Find out how high you'd like the cat flap (normally it's at belly height). Then, mark this area on your door and use the template included to guide you when drilling.

If you have a small kitten you can prop the door open a bit and gradually allow it to pass through. Reward it when it goes through.

Take a measurement of the door

A cat flap allows your pet to enter and exit your home at the time that is convenient for you. This can help keep your cat healthy as it will ensure that it gets enough exercise and will also allow it to go back inside if it is trapped outside during bad weather. It can also cut down on the amount of time you need to spend letting it out or in. It will also help keep your home safe by letting you know when it has gone out.

It is important to ensure that the cat flap is installed correctly in order to prevent your pet from being forced through or escaping through it by other animals (e.g. dogs). It is crucial to determine the height of your pet's belly and the doorway of your house to ensure that the flap is at the right height. You can adjust the height of your flap in case your cat flap bifold doors is taller or less than the average.

The next step is to utilize a spirit level mark the centre of the door, where you will be installing the flap. Then, using the markings as a guideline, cut out the contour of the flap using the help of a jigsaw. After you've cut the area out then sand the edges to create smooth surfaces. Drill any necessary holes.

fitting cat flap in upvc door panel a cat flap should not take longer than two hours. The process is a bit more challenging if you need to put it in a uPVC door or composite one. This is because these doors come in various thicknesses, which can impact the way the holes are cut. We always suggest to contact an expert when this is your first experience working with glass.

Measure Your Cat

You will not have to spend hours of ignoring the pet meow to be let in or out. This is particularly helpful when your cat is inside in all weathers while you are at work.

If you are planning to install a cat flap in your door, it is crucial that you take measurements of your cat prior to attempting the task. It might seem like a simple task, but it's important to measure your cat correctly. Otherwise, your pet may have difficulty putting it in use.

First, ensure that your cat is calm prior to taking measurements. You will have to hold your cat in a position that they are unable to move. Also, ensure that the measuring tape is flat and not curved against their body. You can get an accurate measurement by keeping the measuring tape or the ruler flat against the body of the animal from the top to the bottom.

Once you have your cat's measurements and measurements, you need to look at the door to decide where to put the flap. Place the flap at the level of your cat's belly. This will allow them to go through the door without much effort. This will also prevent the flap from making lots of noise when it swings open and shut.

You should also think about the thickness and the structure of the uPVC door or composite. Although timber doors are of the same thickness, uPVC and composite doors are different in their overall construction and this can make the installation of a cat flap more complicated as you will need to ensure that the hole you cut is the correct size for your pet.

You can also use the template drawing included in the instructions to mark the location of the hole on the door. This will enable you to determine where the hole needs to be placed and ensure that the template is positioned properly on the door. It is also beneficial to use a spirit-level to ensure that the template sits flush against the door.

Cut the Flap

Before you can put in your cat flap installation flap, you'll have to cut the door panel to make it large enough for it. This can be a challenging job and it is recommended that you seek out the assistance of an expert cat flap fitter for this step if you don't have the skills or experience to do it yourself. You can also consult the instructions provided with the kit to discover how to do it right.

To do this, you will need to take a measurement of the height of your cat's or kitten's belly. Use this as an indication point. A good guideline is to put the flap of your cat about 10 centimeters away from the ground since this is the typical height of the cat's belly. This way, your cat will be able to move through the flap with ease and it will also give any other cats or curious neighbours an issue when trying to leave or enter.

The position of the cat flap on the door using the pencil. Then, if your kit comes with a paper template, lay it on top of the door and use the markings to drill holes in every corner of the template. Then, you'll be able to cut out the template and replace it with the cat flap.

You can install your cat flap yourself on the door made of wood or uPVC when you're confident using a Jigsaw. Be sure not to cut into the mullions or rails that run vertically of your door. You can use a Jigsaw to cut your panel into a circle or square depending on the way you want it. Remember to take your time and don't force the jigsaw to cut faster.

Once the hole is cut, carefully place your cat flap in its new home. Make sure that it is solidly secured. If it features caps for screws, then put these caps onto the protruding screws. After the screws are installed then sand the rough edges and seal any gaps. This will prevent drafts from entering your home.

Install the Flap

If you have a basic cat flap, you can leave it open and encourage your pet to walk through by putting a little bit of cat food in front of the door. You can also try pushing the cat through using your hands or with a stick. Once your pet has become comfortable walking through the flap, it will be in a position to move as it pleases. This allows you to let it in and out as it wishes.

It is possible to install an animal flap into a UPVC door or a glass door, but it might not be as simple as putting one inside a wooden exterior door. This is because UPVC doors and some types of glass doors don't have an even thickness. This could have a significant impact on the way you cut the hole for the flap, and can also affect whether your flap will fit properly once it's installed.

The mounting kit might include a template showing you where to drill holes. If the kit doesn't include an example, you can photocopy it to create your own. When cutting, it's important to keep the jigsaw from being pushed too hard so that you don't create a bigger hole than necessary in your door.

Some cat flaps come in circular shapes, which can be more difficult to put in. If you have a round flap, ensure that the hole is located in the correct spot on the door. In the event that it is not, the cat might not be able use it, and could be stuck outside the whole day (or night).

Some models of cat flap come with locks that allow you to regulate the time your cat comes and goes. These can be very useful if you're concerned about your cat going out at night only to come back in due to the darkness, or you're at work for the entire day. Some locks can be used for entrance or exit, while others can be locked both ways. This is useful for Fitting A cat flap older cats or sick cats who do not want to venture out in cold weather.