Fitting A Cat Flap

It might seem daunting to install the flap for your cat but with the right instructions, it's not too difficult. Determine how high you would like the flap to be (normally it's at the belly height). Mark this point on your door and then use the included template as a guide when drilling.

If you have a kitten that is still a baby and you want to keep the door open, gently prop it slightly open and encourage it to pass through. Reward the kitten every time it moves through.

Measure the Door

A cat flap lets your pet to enter and exit your home at any time. This can keep your cat healthy as it will ensure it gets enough exercise and will also allow it to go back inside if it is trapped outside during bad weather. This will reduce the amount of time you have to let your cat flap installation in glass doors near me in or out and make your home safe by notifying you when it has left.

However, it is essential that the flap for your cat is properly fitted to stop your pet from being able to escape through it or be pushed through by other animals (e.g. dogs). It is important to measure the height of your pet's stomach and the height of the doorway in your home to ensure that the flap is at the proper height. You can adjust the height of your flap if your cat is smaller or taller than average.

The next step is to use a spirit level to mark the centre of the door, where you will put the flap. Then, using the marks as an outline, cut the contour of the flap with a jigsaw. Once you've cut the area, sand the edges of the door to create smooth surfaces. You can then drill any fixing holes needed.

The process of fitting the cat flap isn't as difficult as you think, and it shouldn't take more than two hours to complete the entire task from start to the end. The process can be slightly more difficult if you have to install it on the case of a uPVC door or a composite one. This is due to the fact that these doors with cat flap come in various thicknesses, which can affect the way holes are cut. We recommend to consult with an expert for your first experience with glass.

Measure Your Cat

You will not have to spend hours of ignoring the cat's meows to be let in or out. This is especially useful if your cat is trapped in the house during all seasons when you are at work.

It is crucial to first measure your cat before attempting to install. While it may seem a simple operation it is important to measure the right way or your cat will find it difficult to use.

Firstly, make sure your cat is calm and not stressed prior to taking the measurements. You'll need to keep them in a position where they cannot move and ensure that the measuring tape or ruler is flat against their body and not bending in any place. You can take a precise measurement by keeping the measuring tape or Cat Flap Step ruler flat against the body of the animal from the top to the bottom.

Once you have your cat's measurements and measurements, you need to look at the door to decide where to place the flap. Position the flap at the level of your cat's belly. This will allow them to pass through the door with minimal effort. This will also prevent the flap from making a lot of noise as it opens and closes.

You should also think about the thickness and the structure of the uPVC door or composite. While timber doors are all of the same thickness, uPVC and composite doors are different in their overall structure, which can make fitting a cat flap more complicated as you will need to make sure that the hole you cut is the right size for your pet.

You can make use of the template included in the instructions to mark the position of the hole on the door. This will help you to see the location where the opening should be and also make sure the template is correctly positioned on the door. Utilizing a spirit level to make sure that the template is sitting flush against the door will be very helpful.

Cut the Flap

You'll need to make an opening in the door panel to install your cat flap prior to you can install it. It's a challenging task so it's recommended you engage a professional to help you if you lack the skills or experience. You can also refer to the instructions included with the kit to learn how to do it correctly.

To do this, you have to determine the height of your cat's or kitten's belly. Use this as an indicator point. In general put the flap approximately 10-15 centimeters above the ground. This is the standard height of the belly for cats. This will let your cat pass through the flap easily and make it difficult for other cats or naughty neighbours to enter or exit.

Once you've determined the location where the cat flap needs to be placed, mark this position on the door with pencil. If your kit has the template put it on top of the door. Utilize the markings on the template to drill holes at each corner. Then, you should be able cut out the template and replace it with the flap for cats.

If you are installing your cat flap in an entryway made of wood or uPVC, you can do this yourself if you feel confident enough to handle using a jigsaw. Be sure to not cut into any of the door's mullions or vertical rails. You can use a jigsaw cut the panel into a square or circle according to the design of your cat flap step flap. Be patient and don't make the jigsaw cut faster.

Once the hole is made, carefully place the cat flap in its new home. Make sure that it is securely secured. If it has caps on the screws, then place these caps onto the protruding screws. Once the screws are in place, sand the rough edges of the cut, and then apply sealant around any gaps to ensure there are no draughts coming into your home.

Fit the Flap

If you have an ordinary cat flap, you can help your pet through it by placing a small amount cat food on the front of the door. Alternately, you can push the cat through using your hands or with a stick. Once your cat is used to walking through the flap it will be able to come and go whenever it wants. This lets you let it in and out as it wishes.

It is possible to put an animal flap into the UPVC doors or glass door, however it might not be as easy as installing one inside a wooden exterior door. This is due to the fact that the UPVC doors and certain types of glass doors do not have an even thickness. This could have a dramatic effect on the way you cut the opening for the flap and could affect the way your flap will fit properly once it's installed.

Based on the type of cat flap you select It could be equipped with a mounting kit and a template that will show precisely where to drill the holes for it. If the kit doesn't include a template you can create one on your own. When cutting, it's important to not push the jigsaw far enough to make a larger hole than necessary in your door.

The majority of cat flaps are rectangular or square in shape but there are also some which are circular, and they are typically more difficult to fit. If you have a circular flap, make sure that the hole is located in the correct place on the door. Otherwise, the cat may not be able to use it, and could be locked outside for the entire day (or at night).

Some cat flaps have locks which permit you to manage the time your cat comes and goes. These are very helpful when you're worried about your pet going out at night and Cat flap Step coming back in due to the darkness, or you're working all day. The lock can be used to allow entry or exit, and some locks can be locked in both directions, which allows you to close the door completely. This is especially helpful for sick or elderly cats who aren't willing to go out in bad weather.